5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front 6. reverse above and then remove filter-vent housing and scrape off old seal install new seal 7. re-connect power,gas and vent use again Step 2 - Support the top. google_ad_width = 160; All of the information for this roller replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley //-->, Copyright 2020 Michael Sakowski Questions or Comments? This is especially needed in this model since the opening around the wire could easily damage or even shear off wires if the top fell over. I had the dryer completely apart to replace the rollers… Use a putty knife to press the clips holding the lid in place (Image 1). To complete this repair, you will need to remove the front panel as … /* repairdryerbottom468x60, created 9/11/10 */ Perhaps you will notice that the left roller is more worn out than the right one. Unlike other dryers, however, you don't have to remove the tumbler to replace the belt on this model. All parts that I wanted were available via Amazon. The Sears site used a zero but I have seen some search results use an "o". google_ad_height = 60; They will be below the drum. Drum rollers on electric and gas dryers support the drum while it rotates by means of a belt. 2 pcs Find the Right Dryer Belt with Repair Clinic To find the right dryer drum belt that fits your dryer, type the full model number of the dryer into the Repair Clinic.com search bar. To do lift the drum out, you will need to first remove the belt from the motor and idler pulley as shown in the photo below. You can make some repairs with the drum in place, such as replacing the idler pulley or front felt ring. Step 3 - Disconnect the door switch and remove two front bolts. This video will show you how to replace the rollers on a Whirlpool/Kenmore/Lady Kenmore 27" wide dryer. To check the rollers, first disconnect power from the dryer. Once the two bolts of Step 3 are removed, you may lift away the dryer front. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Then simply grab the drum and lift it out and away. Disconnect the power to avoid shock, damage, injury, or death! //-->. See take apart info - Slide show for taking apart an old Maytag style dryer with the L shaped door. Lift the lid. If … This easy picture guide walks through each step. Note: This video is intended to give you the general idea of the part replacement procedure. This video provides step-by-step repair instructions for replacing the belt on a Maytag dryer. Make sure to disconnect the power, gas, vent lines Step 4 - Remove the dryer front. Your first step is to remove the screws at the bottom of the front panel. From the looks of it, the flimsy plastic pulley that is provided will only last 3-6 years before cracking up from the heat. Once the drum is out you have easy access to all parts within the cabinet. This video provides step-by-step repair instructions for replacing the belt on a Maytag dryer. Some Maytag dryers are equipped with a safety device called a belt switch. Posted by Jeff Brown on 8th Jan 2020 The belt that comes with this kit is not the correct one for the Maytag Dryer. How to Replace Rear Support Rollers on a Maytag Dryer. As with any repair, be sure you unplug the appliance before beginning. instructions w/ belt for Whirlpool, online vids not helping; they are all showing a motor pulley that is free on one end, so the belt can be looped over the end of it, then seated on pulley. In the lower left photo, you see a wire connection to the door switch - this must be disconnected - just lift the plastic tab a little to allow the connection to be pulled apart. When putting dryer back together make sure felt is straight. Release the wires from the front bulkhead. Step 6 - Reassemble dryer by reversing steps 1-5. /* 160x600, created 9/6/10 */ Parts for this dryer. Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch. With any dryer, make absolutely sure that you replace the old belt with a new one made especially for the dryer. zero?) Remove the lint filter and then remove two screws that hold the lint filter housing to the dryer top, as shown below on the left. google_ad_client = "pub-2699604619725799"; Once you know how to replace a Maytag Neptune clothes dryer belt, you will have your appliance working again. Use a rope to secure the top from above as shown below to avoid damaging the wires. This is a common occurrence, but you need to replace both at the same time. In some cases you might need to replace the front bearings/glides as well. Start doing it yourself with the confidence that comes with 100+ years of experience. A short upward motion will easily free it from two lower hangers. The most common reasons for replacing the drum support roller are when the dryer makes noise, stops turning during the cycle, or won’t turn at all. The Bravos line of dryers, made by Maytag, uses a belt to rotate the drum that tumbles the clothes. 1. disconnect power,gas and vent lines 2. pop off top of unit 3. remove front of dryer 4. lay unit on its back 5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front 6. reverse above and then We replaced all the parts. If the plug can be reached without moving the dryer, the dryer probably won't have to be moved. Email Me! Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips! How to replace a tumble dryer belt, Whirlpool, Bauknecht, Bosch, Ignis, Maytag & Proline This video will show you how to replace and change the belt on your tumble dryer for models listed below. Then remove the drum by removing the belt Get shopping advice from experts, friends and the community! To replace a broken belt, pull the drum, place the new belt over it, and then thread the belt over the idler pulley as shown above while either someone holds the drum in place or you support it some other way. Unthread the old belt from the pulley and motor shaft and pull the belt out. If your dryer thumps, scrapes or squeals, the problem could be a worn or broken drum support roller. This DIY repair guide and video explain how to easily replace the dryer drum support roller. Here is a video that shows you how to disassemble the Maytag Neptune dryer and change the rollers and belt. How to Replace Dryer Belt for Maytag SDE515DAYW Noisy #AP6009126 Step by step instructions on how to replace a Dryer Belt for Maytag SDE515DAYW Noisy #AP6009126. If the belt breaks mid-cycle, the switch turns off your dryer and keeps it off until the damaged belt is replaced. How to replace a belt on a maytag dryer. Over time, this belt can wear out or snap and stop your dryer drum from rotating. DE 303, series 05, seriel number(NNN) NNN-NNNN. google_ad_height = 600; ROLLERS Another cause for your Maytag dryer being noisy is the rollers.